syntax-check command
Hi,
I have to write a report to conduct a syntax check on the custom program selected through the selection screen and capture all the errors in the program including the line numbers for the errors.
I have tried using the 'syntax-check' command however it will capture only the first error in the program.
Can someone help me with the same and let me know if there is any other command that can be used or any other alternative.
Thanks in advance.
I have to write a report to conduct a syntax check on the custom program selected through the selection screen and capture all the errors in the program including the line numbers for the errors.
I have tried using the 'syntax-check' command however it will capture only the first error in the program.
Can someone help me with the same and let me know if there is any other command that can be used or any other alternative.
Thanks in advance.
gesponsert ⓘ
Stellenangebote auf ABAPforum.com schalten
kostenfrei für Ausbildungsberufe und Werksstudenten
kostenfrei für Ausbildungsberufe und Werksstudenten
Beitrag
von Frank Dittrich (Expert / 674 / 0 /
15
)
»
It is possible to capture all errors.
But it doesn't make much sense, because the syntax checker usually gets so confused by the first error that all subsequent error messages should better be ignored until you fix the first one.
But it doesn't make much sense, because the syntax checker usually gets so confused by the first error that all subsequent error messages should better be ignored until you fix the first one.
Hello Frank,
Thank you for your immediate reply. I would agree with you on your reply however I would be grateful if you can let me know the procedure for capturing all the errors including the line numbers as this is for an upgrade tool that we are developing and what we need is a rough idea to make the assessment of the system.
Thanks and Regards.
Thank you for your immediate reply. I would agree with you on your reply however I would be grateful if you can let me know the procedure for capturing all the errors including the line numbers as this is for an upgrade tool that we are developing and what we need is a rough idea to make the assessment of the system.
Thanks and Regards.
Beitrag
von Frank Dittrich (Expert / 674 / 0 /
15
)
»
In SY-SAPRL 6.20, it's mentioned in the documentation (press F1 on SYNTAX-CHECK).
It's not documented in release 4.x .
In 4.6B I've encountered several bugs when searching for all errors (instead of just the first error).
I didn't check whether all the bugs I discovered in 4.6 have been fixed in 6.20.
From/to which SY-SAPRL?
Or do you want to sell a general purpose update tool?
Wich releases do you want to support?
A SYNTAX-CHECK which displays all errors is not at all useable for your purpose, because it's poorly implemented.
(Much worse than what you might expect if you compare the results with the diagnostics of a C compiler.)
There are better options than a syntax check.
It's not documented in release 4.x .
In 4.6B I've encountered several bugs when searching for all errors (instead of just the first error).
I didn't check whether all the bugs I discovered in 4.6 have been fixed in 6.20.
Are you planning an update?this is for an upgrade tool that we are developing and what we need is a rough idea to make the assessment of the system
From/to which SY-SAPRL?
Or do you want to sell a general purpose update tool?
Wich releases do you want to support?
A SYNTAX-CHECK which displays all errors is not at all useable for your purpose, because it's poorly implemented.
(Much worse than what you might expect if you compare the results with the diagnostics of a C compiler.)
There are better options than a syntax check.
Seite 1 von 1
Vergleichbare Themen
9
Antw.
Antw.
4110
Views
Views
8
Antw.
Antw.
3756
Views
Views
3
Antw.
Antw.
2072
Views
Views
4
Antw.
Antw.
2058
Views
Views
0
Antw.
Antw.
3598
Views
Views
Syntax Fehler nach update über SPAM
von Franzman1981 » 03.06.2008 10:29 • Verfasst in Exchange Infrastructure
von Franzman1981 » 03.06.2008 10:29 • Verfasst in Exchange Infrastructure
Frage die ABAP Experten
Über diesen Beitrag
Unterstütze die Community und teile den Beitrag für mehr Leser und Austausch
Aktuelle Forenbeiträge
Umherspringende Methoden im quelltextbasierten Class Builder
vor 22 Stunden von ralf.wenzel 104 / 10293
vor 22 Stunden von ralf.wenzel 104 / 10293
Newsletter Anmeldung
Keine Beiträge verpassen! Wöchentlich versenden wir lesenwerte Beiträge aus unserer Community.Die letzte Ausgabe findest du hier.
Aktuelle Forenbeiträge
Umherspringende Methoden im quelltextbasierten Class Builder
vor 22 Stunden von ralf.wenzel 104 / 10293
vor 22 Stunden von ralf.wenzel 104 / 10293