Rahmen anpassen SAP-Script

Rahmen anpassen SAP-Script

Hallo zusammen,

ich wollte gerne den Rahmen von einem Fenster bei einem SAPScript anpassen (Siehe Bild 1).

Ich dachte eigentlich, dass man das hier anpasst (Siehe Bild 2). Leider hat es keine Veränderung ergeben, als ich die cm-Zahl nach oben gesetzt habe und jetzt steh ich ein bisschen auf dem Schlauch.

Weiß jemand von man den Rahmen von diesen Fenstern von SAP-Scripts anpasst?

Vielen Dank im Voraus.

Re: Rahmen anpassen SAP-Script

Hallo L0w-RiDer,

so gehts:

Boxes, Lines, Shading: BOX, POSITION, SIZE

The BOX, POSITION and SIZE commands for drawing boxes, lines and shadowing can be used for specifying that within a layout set particular windows or passages of text within a window are to be output in a frame or with shadowing.
The SAP printer drivers that are based on page-oriented printers (the HP LaserJet driver HPL2, the Postscript driver POST, the Kyocera Prescribe driver PRES) employ these commands when outputting. Line printers and page-oriented printers not supported in the standard ignore these commands. The resulting printer output may be viewed in the SAPscript print previewer.
Syntax:

1. /: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]
2. /: POSITION [XORIGIN] [YORIGIN] [WINDOW] [PAGE]
3. /: SIZE [WIDTH] [HEIGHT] [WINDOW] [PAGE]

BOX Command
Syntax
/: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]
Effect: draws a box of the specified size at the specified position.
Parameters: For each of XPOS, YPOS, WIDTH, HEIGHT and FRAME both a measurement and a unit of measurement must be specified. The INTENSITY parameter should be specified as a percentage between 0 and 100.

1. XPOS, YPOS: Upper left corner of the box, relative to the values of the POSITION command.

Default: Values specified in the POSITION command.
The following calculation is performed internally to determine the absolute output position of a box on the page:
X(abs) = XORIGIN + XPOS
Y(abs) = YORIGIN + YPOS

2. WIDTH: Width of the box. Default: WIDTH value of the SIZE command.
3. HEIGHT: Height of the box. Default: HEIGHT value of the SIZE command.
4. FRAME: Thickness of frame.
Default: 0 (no frame).

5. INTENSITY: Grayscale of box contents as % .

Default: 100 (full black)

Measurements: Decimal numbers must be specified as literal values (like ABAP numeric constants) by being enclosed in inverted commas. The period should be used as the decimal point character. See also the examples listed below.
Units of measurement: The following units of measurement may be used:

· TW (twip)
· PT (point)
· IN (inch)
· MM (millimeter)
· CM (centimeter)
· LN (line)
· CH (character).

The following conversion factors apply:

· 1 TW = 1/20 PT
· 1 PT = 1/72 IN
· 1 IN = 2.54 CM
· 1 CM = 10 MM
· 1 CH = height of a character relative to the CPI specification in the layout set header
· 1 LN = height of a line relative to the LPI specification in the layout set header

/: BOX FRAME 10 TW
Draws a frame around the current window with a frame thickness of 10 TW (= 0.5 PT).
/: BOX INTENSITY 10
Fills the window background with shadowing having a gray scale of 10 %.
/: BOX HEIGHT 0 TW FRAME 10 TW
Draws a horizontal line across the complete top edge of the window.
/: BOX WIDTH 0 TW FRAME 10 TW
Draws a vertical line along the complete height of the left hand edge of the window.
/: BOX WIDTH '17.5' CM HEIGHT 1 CM FRAME 10 TW INTENSITY 15
/: BOX WIDTH '17.5' CM HEIGHT '13.5' CM FRAME 10 TW
/: BOX XPOS '10.0' CM WIDTH 0 TW HEIGHT '13.5' CM FRAME 10 TW
/: BOX XPOS '13.5' CM WIDTH 0 TW HEIGHT '13.5' CM FRAME 10 TW
Draws two rectangles and two lines to construct a table of three columns with a highlighted heading section.

Mit freundlichen Grüßen
Matthias Alpmann

Re: Rahmen anpassen SAP-Script

Hallo,

auch das Formular aktiviert?

Gruß Wolfgang

Re: Rahmen anpassen SAP-Script

Okay, super.

Jetzt hats funktioniert.